Condensation on windows in winter means the air inside your house is holding more moisture than the cold glass can stand. Lower the indoor humidity, ventilate, and keep warm air moving across the glass: turn the furnace humidifier down or off, make sure the heat recovery ventilator is running, run the bathroom and kitchen fans, open the blinds at night, and wipe the sills dry each morning. Water between the two panes is different: the seal has failed and the glass unit needs replacing. Water on the outside of the glass at sunrise is harmless. Natural Resources Canada puts the whole thing in one line: the risk rises as the weather gets colder and as the inside humidity rises. This page explains why a Barrie house fogs up in January, how much humidity your windows can actually take, the fixes in the order that works, and where your HRV and ERV cleaning in Barrie fits in.
Why windows sweat in winter
Warm air holds more water vapour than cold air. When warm, moist indoor air touches a surface colder than its dew point, it gives that water up, as fog first, then droplets, then frost or ice if the surface is cold enough. In a heated house in winter, the coldest surface in almost every room is the window glass, then the frame and sash, then the weatherstripping along the edges.
Natural Resources Canada's guidance on condensation describes it exactly that way: condensation often happens in colder weather when moist air inside the home meets cooler surfaces, and it shows up on the glass, on the frames and sashes, and near the weather seals. Two things move the line. The colder it is outside, the colder the glass gets. The more moisture in the indoor air, the higher its dew point. Either one alone can tip a window into fogging; together, on a January cold snap, they tip almost every window in a tight house.
That is why the same house can be dry in November and streaming in January without anything changing indoors. The moisture level stayed put. The glass got colder.
Window condensation is a humidity reading you can see. The glass is telling you the air is wetter than the house can hold at today's temperature.
Inside, outside or between the panes
Where the water sits tells you what kind of problem you have. Look before you do anything else.
| Where the water is | What it means | What to do |
|---|---|---|
| Inside surface of the glass | Indoor air is too moist for how cold the glass is | Lower humidity, ventilate, keep air moving over the glass |
| On the frame, sash or weatherstrip | Same cause, plus a cold edge or an air leak at the seal | Same fixes; check the weatherstripping |
| Between the two panes | The sealed glass unit has failed | Replace the insulating glass unit; humidity changes will not fix it |
| Outside surface, around sunrise | Cool, calm, humid night outdoors; common with efficient glass | Nothing; it burns off |
Natural Resources Canada covers both of the less obvious rows: condensation between the panes means the seal is broken and the insulating glass unit should be replaced, and condensation can form on the outside of the glass around sunrise after a cool, calm, humid night, which is weather rather than a fault in the house. This page is about the first two rows, the ones you can fix with how you run the house.
How much humidity your windows can take
There is no single right number, because the limit is set by how cold it is outside and how good your windows are. Health Canada's guide to addressing moisture and mould says to keep relative humidity between 30% and 50%. In a Barrie winter, the windows usually decide where in that range you can sit.
The clearest way to see it is an old reference table that building scientists still quote. The National Research Council's Canadian Building Digest 1, Humidity in Canadian Buildings (N. B. Hutcheon, 1960), worked out the highest indoor relative humidity a room at about 21°C (70°F) can carry before its windows start to fog, with a wind blowing outside:
| Outdoor temperature | Single glazing | Double glazing |
|---|---|---|
| About -7°C (20°F) | 24% | 53% |
| About -18°C (0°F) | 12% | 41% |
| About -29°C (-20°F) | 6% | 32% |
Those figures are for 1960 windows, and a modern double- or triple-glazed unit with low-e glass and warm edge spacers does better than the double glazing in that table. The shape of it has not changed, though. Every step colder outside lowers the ceiling. A setting that is fine at -5°C can stream the windows at -20°C. The same digest made the point that raising indoor humidity above the level where the windows fog gains you very little, because the extra moisture just moves to the cold surfaces and piles up there.
So the working rule is simple. Find the humidity at which your windows stay clear on a normal winter day, and turn it down when a cold snap comes. A hygrometer, a small digital humidity gauge, tells you the actual reading; a humidistat dial only tells you what you asked for. Our guide to furnace humidifier settings for winter covers the setting itself and why newer homes often need no added moisture at all.
Where the moisture comes from in a Barrie house
A house makes its own humidity every day. In winter, with the windows shut, it has fewer ways out. The usual sources, roughly in order of how often they are the culprit:
- Showers and baths. Health Canada lists bathing and showering first among the daily activities that drive moisture problems, especially when the bathroom fan is not working, not vented outside, or not used.
- Cooking. Boiling pots put a lot of water into the air in a short time. Health Canada's advice is to use the range hood every time, preferably on its highest setting.
- Laundry. A clothes dryer that is not vented outside, or a vent line so clogged that moist air leaks back into the laundry room, adds a surprising amount. So does a rack of clothes drying indoors, which Health Canada flags directly.
- A furnace humidifier set too high, or one with a stuck valve that keeps feeding water after the house has had enough.
- A damp basement. Moisture from the foundation and slab rises into the rest of the house through the stairwell and the return air.
- People, pets and plants. Breathing and houseplants add a steady background load, which is why bedrooms with closed doors often have the worst windows by morning.
- A new house drying out. Lumber, concrete and drywall release their construction moisture over the first winters. A new home in one of the south-end or west-end subdivisions can fog its windows with the humidifier off.
If the condensation is worst in one room, the source is usually in or near that room: the bathroom, the kitchen, the laundry, or a bedroom with the door shut and the blinds drawn.
The fixes, in the order that works
Start at the top. Most houses are clear by the third or fourth step.
- Measure first. Put a hygrometer in the main living area and another in the worst room. If the reading is well above what your windows can carry at today's temperature, you know the job is to dry the air, not to buy new windows.
- Turn the humidifier down, or off. If the furnace has a humidifier, drop it until the windows clear, and lower it again on cold nights. In a tight house it may not need to run at all.
- Make sure the HRV is on. Natural Resources Canada says it plainly: if you have a heat recovery ventilator, make sure it is running. An HRV switched off to save money in winter is one of the most common reasons a newer house streams its windows.
- Use the exhaust fans properly. Bathroom fan during every shower and for at least 30 minutes after, which is Health Canada's figure. Range hood on high while cooking. If the bathroom fan cannot hold a square of toilet paper to its grille, it is not moving air; our guide to bathroom exhaust fan cleaning walks through the test and the duct behind it.
- Keep warm air moving across the glass. Natural Resources Canada notes that air flowing across the glass keeps it warmer, and that deep sills, closed drapes and blinds, and even nearby furniture block that air and let cold air collect at the window. Health Canada says the same about heavy curtains. Open the blinds at night, pull the couch off the heat register under the window, and make sure that register is open.
- Check the dryer vent. The dryer should exhaust outside through a clear line, with the outside hood free of snow and lint. Our page on a frozen dryer vent in winter covers the snowbank and stuck-flap problem.
- Dry the basement. Health Canada recommends a dehumidifier in damp areas such as basements, run with the windows closed and the bucket emptied or drained.
- Wipe the sills every morning while you work through the rest. Health Canada's advice is to dry window frames and sills daily so water does not drip and start mould.
If you do all of this and one window still streams while the others stay clear, look at that window rather than the air: a failed seal, a cold frame, missing weatherstripping or an air leak around the trim. That is a job for a window contractor, not for us.
The HRV in winter
Many newer Barrie homes have a heat recovery ventilator. It runs stale, moist indoor air out through a core while bringing fresh outdoor air in, and the core passes heat from the outgoing air to the incoming air so you are not heating the outdoors. In winter, the outgoing air is the moist air and the incoming air is cold and dry, so a working HRV is one of the main ways a tight house gets rid of its moisture.
It only works if air actually moves through it. CMHC's guidance on how to maintain a heat recovery ventilator gives the homeowner's list:
- Clean or replace the filters every two months.
- Clear snow and frost from the outside vents during the winter, along with any debris.
- Check the condensate drain by pouring water into the drain pans and making sure it runs freely.
- Vacuum and wash the core according to the owner's manual.
- Once a year, remove the grilles on the duct ends and vacuum inside the ducts.
- Call an HRV service technician if a more thorough cleaning is needed.
The last item is where we come in. A clogged core, packed filters and dusty supply and exhaust runs cut the airflow, and an HRV that hums along moving half its rated air will not keep up with a January cold snap. We clean the core, filters, drain pan and the duct runs to the grilles; the HRV and ERV cleaning page lists what is included. If your unit is an ERV, an energy recovery ventilator, it passes some moisture back into the house along with heat, so it dries the air less than an HRV does; your manual or an installer can tell you which you have and how it should be set for winter.
When condensation turns into mould
Water that sits on a sill night after night is the start of mould. The first signs are grey or black spotting in the corners of the frame, on the caulking, on the window return and in the gap behind the blinds. The same air that fogs the glass also condenses in other cold spots: the corners of outside walls, the back of a closet on an outside wall, behind a dresser pushed against one.
Small patches on a hard surface are usually a cleaning job for the homeowner, and the lasting fix is drying the air so it stops coming back. Health Canada's moisture guide is the right reference for that. Larger areas, mould on drywall, or mould that returns after you have dried the house out are a job for a mould remediation contractor, and if anyone in the house has health concerns, that conversation belongs with a doctor, not with us.
Window mould does not usually mean the ducts are mouldy. Ducts get damp from a humidifier set too high, a leaking humidifier, an air conditioner coil that does not drain, or water in a basement run. Our page on duct mould cleaning in Barrie explains when cleaning the ducts helps, and when the honest answer is that the moisture source has to be fixed first and cleaning would be wasted money.
Older and newer Barrie homes
Barrie sits on the southern edge of Ontario's snowbelt, and the heating season runs from about October to April. The condensation problem looks different in the two broad kinds of house in the city.
- Older homes downtown and in the established east-end neighbourhoods tend to leak air. Cold, dry outdoor air keeps coming in, which keeps the indoor humidity low, so these houses often have less condensation overall. When they do fog, it is usually one room with a big moisture source, a window with a worn seal, or an older aluminium frame that runs cold all winter.
- Newer homes in the south-end and west-end subdivisions are built tight. They hold the moisture from showers, cooking and people, which is exactly why they have HRVs. When one of these houses streams its windows, the first questions are whether the HRV is on, whether its filters and core are clean, and whether a humidifier is adding water the house does not need.
Either way, the first heating season after a renovation or in a brand-new house is often the worst, because the building materials are still giving up moisture.
Where we fit, and where we do not
We clean the parts of the air system that move moisture out of the house: HRV and ERV cores, filters and duct runs, bathroom fan ducts, dryer vents, and the ductwork itself. If the reason your windows sweat is an HRV that cannot breathe or a dryer line that leaks moist air back into the house, cleaning fixes it. If the reason is a humidifier set at 45% or a family of five showering with the fan off, cleaning does not, and we will say so.
We do not replace windows or glass units, install or rebalance HRVs, service humidifiers, or do mould remediation on walls and ceilings. The published prices the work is built on:
| Job | What's included | Price |
|---|---|---|
| HRV or ERV cleaning | Core, filters, drain pan and the duct runs to the grilles | Quoted with your duct cleaning, by unit type and access |
| Dryer vent cleaning | Full line from the machine to the outside hood | $99 to $149 on its own |
| Air duct cleaning, most Barrie homes | Every supply vent and cold-air return, trunk lines, furnace blower and cabinet | $249 to $429 |
The full breakdown by home size is on the duct cleaning cost page, and the main service is air duct cleaning in Barrie. The price is confirmed before we start.
Frequently asked questions
Why do my windows have condensation on the inside in winter?
Because the indoor air holds more moisture than the cold glass can stand. When warm, moist air meets glass colder than its dew point, the water comes out on the glass. It gets worse as the weather gets colder and as the indoor humidity rises, which is why a house that was clear in November can stream in January.
Is condensation on windows bad?
A little fog on the coldest morning is normal. Water that runs down the glass and sits on the sill every day is a problem, because it rots wood frames, stains the trim and starts mould on the frame and caulking. Health Canada advises drying window frames and sills daily while you lower the humidity.
How do I stop condensation on my windows in winter?
Lower the indoor humidity and ventilate: turn the furnace humidifier down or off, keep the HRV running, run the bathroom fan for at least 30 minutes after a shower and the range hood on high while cooking, open blinds and curtains at night, keep furniture off the register under the window, and dry the basement with a dehumidifier if it is damp.
What humidity should my house be in winter to avoid condensation?
Health Canada's range is 30% to 50%, but in a Barrie winter the windows set the limit, and it drops as the outdoor temperature drops. Find the reading at which your windows stay clear on a normal winter day with a hygrometer, and turn the humidity down further during a cold snap.
Why is there condensation between the panes of my window?
The seal on the sealed glass unit has failed and moist air has got into the gap. Natural Resources Canada's advice is to replace the insulating glass unit. Changing the indoor humidity will not fix it.
Does an HRV help with window condensation?
Yes. A heat recovery ventilator exhausts moist indoor air and brings in drier outdoor air, and Natural Resources Canada's first tip for condensation is to make sure the HRV is on. It only works if the filters and core are clean: CMHC says to clean or replace the filters every two months and clear snow and frost from the outside vents in winter.
Can dirty ducts cause condensation on windows?
Not usually. Condensation comes from too much moisture in the air, not from dust in the ducts. The exceptions are a clogged HRV, a bathroom fan duct that cannot move air, or a dryer line leaking moist air back into the house; cleaning those fixes the airflow, and we will tell you if that is not the cause.
Reviewed November 2026.
Prefer to talk? Call
(249) 444-8673We give you a published, all-in price for your home before we start, and clean the system properly under negative air. No $99 ad games.
- Published pricing, locked before we start
- Negative-air, source-removal process
- Honest advice if you don't need it yet
- Dryer-vent lint cleared for fire safety
- Before-and-after shown on the spot
Barrie & Simcoe County
Get a straight quote
Tell us about your home and we’ll come back with a published price and a time. No obligation, no on-site surprise.